| Particular | Specification |
|---|---|
| Load capacity | 5Kn (5000N) |
| No. of load cell | Two (1 N to 10 N ) |
| Unit of Measurement | KGF, Newton & Lbs |
| MATERIAL | Mild Steel |
| OPERATING MODE | Automatic |
| TYPE OF CONSTRUCTION | Load Frame Supported on a Base Plate with Legs Support |
| FORCE MEASUREMENT | By Electronic Load Cells of high accuracy |
| TEST LIMIT | 1N to 5000N |
| FINISH | Powder coated Havel Gray & Blue combination finish and bright chrome/zing plating for corrosion resistant finish |
| USE OF EQUIPMENT | Measurement of Tensile Strength of Fabrics, Thread, cord, Rope, Tapes, Hook Tape /Loop Tape, Zip Fasteners, Button Pull Off etc. |
| WORKING PRINCIPAL | Constant Rate of Extension (CRE) |
| GRIP TO GRIP SEPARATION | Up to 1000 mm, Fabric Test Strip Width – up to 150 mm |
| Speed | variable between 5 mm/minute to 1000mm/minute through Ball Screw |
| Accuracy | Load Measurement - (+/-0.5%) of Load Speed - +/- 0.2% of Set Speed Position Measurement- +/-0.01% of reading Elongation-+/-1% |
| Power | 230 volts, 50Hz. Single phase |
| Type of Tests | Breaking Strength, Elongation at Break, Tenacity, Extension %, Tear Strength, Peel Strength, Shear Strength, Skein Break Test, Load at Specific Extension %, Extension % at specific Load, Various Load Performance Tests of Zip Fasteners |
| TEST STANDARD | ASTM D412, ASTM D429-73, ASTM D624, ASTM D41638-01, ASTM D76, IS 13360-5-7, IS 33400 (Part I-1987) IS 7016 (part-2, 3 & 5), IS 1969 (part 182), IS 1670, IS 1969, IS 4227, IS 4910 Part II, IS 8156, IS 8543 (Part XIII, Sec I), IS 9686, IS 14181 Part II (Annexure, B,C,D,E,F,G,H &J) |
| Clamping Device | Pneumatically actuated clamps with exchangeable clamp inserts of various materials, exchangeable reduction curves, programmable clamp pressure in stages |
| Results | Numerical, Statistical and Graphical output of data |
| Data Storage | Storage in Hard Disk of Computer with data backup facility |
| Power Requirement | 220-240 V, 50 Hz Single Phase AC Supply Data |
| Other Requirement | Test Equipment would be supplied with digital/ LCD display, Inbuilt memory along with computer hardware and software. Must be attached with computer. Printer for printout and graphs of test reports checking and calibration system |
| Accessories | We will provide grips, computer hardware and software, printer, Air compressor and apparatus for checking and calibration of the instrument... |
| Calibration Certificate | Certificate of calibration of the equipment for the entire range of machine from the NABL accredited laboratory would be submitted along with supply. The certificate shall have NABL logo |
| Other |
Result are display in Touch Screen as well as through PC Highly accurate position control with high range of Speed Automatic calculation of results Selectable Have multi display in Kg. pound, Newton mm. cm, inch selectable Safety norms of over load in auto/ manual mode Data lock for calibration Suitable for checking all types of material as per customer requirement. NOTE : Speed can control Through servo motor / servo drive variable speed we are providing from 5 mm to 1000 mm/minute which is possible only through servo motor and touch screen panel where you just put speed on touch screen panel for e.g. 5 mm / minute and the machine with start at desired speed and if you put 1000 mm / minute the machine will start at desired speed Accuracy of the machine should be within its tolerance limit of+ or - 1% Machine have TFT Touch Screen display unit/computerized which can shows load, Elongation, Maximum Load. |
